Neumann AC 20Y-cable with one XLR 5 F connector and two XLR 3 M connectors. It is used to split two-channel signals into two mono channels, when using, for example, the BS 48 i-2 power supply.Other cable lengths are available upon request! For more information, please visit this products webpage
Neumann BCM 104The BCM 104 is ideal for the faithful reproduction of speech and music. This is due, for instance, to the frequency response that is flat up to 3 kHz and then gradually boosted in the higher frequencies. If required, internal switches can be used to compensate for the proximity effect and to reduce the sensitivity by 14 dB. The versatility of the BCM 104 can be seen in its wide range of applications, from news, to round-table discussions, to radio plays, to musical recordings.Features:Large-diaphragm condenser capsuleCardioid directional characteristicCharacteristic, functionally optimized design*Integrated pop protectionIntegrated elastic suspensionIndividual headgrilles for different usersColored rings to identify the replacement headgrillesEasy removal and cleaning of microphone headgrille (with bayonet mount)Mechanical compatibility with standard studio boom armsInternal switches: high-pass and pre-attenuationTechnical Specifications:Acoustical operating principle Pressure gradient transducerDirectional pattern CardioidFrequency range 20 Hz ... 20 kHzSensitivity at 1 kHz into 1 kohm 22 mV/PaSensitivity at –14 dB attenuation 4.4 mV/PaRated impedance 50 ohmsRated load impedance 1 kohmsEquivalent noise level, CCIR1) 18 dBEquivalent noise level, A-weighted1) 7 dB-AMaximum SPL for THD 0.5%2) 138 dBMaximum SPL for THD 0.5% with preattenuation2) 152 dBSignal-to-noise ratio, CCIR1) (rel. 94 dB SPL) 76 dBSignal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) 87 dBMaximum output voltage 10 dBuDynamic range of the microphone amplifier (A-weighted) 131 dBSupply voltage (P48, IEC 61938) 48 V ± 4 VCurrent consumption (P48, IEC 61938) 3.2 mAMatching connector XLR3FWeight 500 gDiameter 64 mmLength 85 mmHeight (without suspension) 110 mm
Neumann BCM 705The BCM 705 is Neumann’s first dynamic microphone. The housing and headgrille are identical to those of the BCM 104; only the green logo indicates that this is something new from Neumann. The principle of reduction to the essentials can be seen in the dynamic capsule with a hypercardioid directional characteristic, specifically designed for speech reproduction at close range. Multi-level isolation from structure-borne noise ensures operation free of interference, even in a lively studio environment. Features:Dynamic capsuleHypercardioid directional characteristicCharacteristic, functionally optimized design*Integrated pop protectionIntegrated suspensionIndividual headgrilles for different usersColored rings to identify the replacement headgrillesEasy removal and cleaning of microphone headgrille (with bayonet mount)Mechanical compatibility with standard studio boom armsMulti-level isolation from structure-borne noiseNo power supply requiredTechnical Specifications:Acoustical operating principle Pressure gradient transducerDirectional pattern HypercardioidFrequency range 20 Hz ... 20 kHzSensitivity at 1 kHz into 10 kohm 1.7 mV/PaRated impedance 200 ohmsRated load impedance 10 kohmsEquivalent noise level, CCIR1) 32 dBEquivalent noise level, A-weighted1) 18 dB-ASignal-to-noise ratio, CCIR1) (rel. 94 dB SPL) 62 dBSignal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) 76 dBWeight 500 gDiameter 64 mmLength 85 mmHeight (without suspension) 110 mm
Neumann DS 100-1Mount to attach two KVF.. capsule extensions of the KM 100 system onto a tripod. Especially suited for holding long KVF.. It is easy to arrange the capsule extensions in parallel or facing each other. The double mount has a 5/8"-27 female thread, plus a thread adapter to connect to 1/2"- and 3/8" stands.For more information, please visit this products webpage
Elastische AufhängungFür Neumann TLM 103, TLM 127, TLM 193 und M 147 Mikrofone.Farbe: nickelFür weitere Informationen, besuchen Sie bitte die Homepage zu diesem Produkt.
Elastische Aufhängung Für Neumann TLM 103, TLM 127, TLM 193 und M 147 Mikrofone. Farbe: schwarz Für weitere Informationen, besuchen Sie bitte die Homepage zu diesem Produkt.
Neumann EA 170This Shockmount is designed for the TLM 170 (R) and M 149 Tube microphones. It has a swivel mount with a 5/ 8"-27 female thread that can be fastened to tripods. Included is a threaded adapter to connect to 1/2"- and 3/8" stands. Black Finish. For more information, please visit this products webpage
Neumann EA 170 mtThis Shockmount is designed for the TLM 170 (R) and M 149 Tube microphones. It has a swivel mount with a 5/ 8"-27 female thread that can be fastened to tripods. Included is a threaded adapter to connect to 1/2"- and 3/8" stands. Black Finish. For more information, please visit this products webpage
Neumann EA 2124 A mtThe EA 2124 A mt is able to accept microphones from 21 to 24 mm in diameter. It has a swivel mount with a 5/8"-27 female thread, plus a thread adapter to connect to 1/2"- and 3/8" stands. For more information, please visit this products webpage
Neumann EA 87The Neumann EA 87 SILVER Elastic Suspension mount. Essential elastic suspension mount for all U 87 users.The Neumann EA 87 SILVER is designed for the U 87 Ai microphone and has a Nickel (silver) finish. It has a swivel mount with a 5/8 inch-27 female thread, plus a thread adapter to connect to 1/2 inch - and 3/8 inch studs.The main features of the Neumann EA 87 SILVER include:Essential elastic suspension mount for all U 87 usersNickel (silver) finishSwivel mount with a 5/8 inch-27 female thread, plus a thread adapterReduce rumble and noise transferred through the microphone stand For more information, please visit this products webpage
Die EA 87 ist für das Mikrophon U 87 Ai vorgesehen. Der schwenkbare Gewindeanschluss hat 5/8'-27-Gang, mit Adapter für 1/2'- und 3Stative.
Farbe: schwarz
Neumann EA 89 AThe Neumann EA 87 SILVER Elastic Suspension mount. Essential elastic suspension mount for all U 87 users.The Neumann EA 87 SILVER is designed for the U 87 Ai microphone and has a Nickel (silver) finish. It has a swivel mount with a 5/8 inch-27 female thread, plus a thread adapter to connect to 1/2 inch - and 3/8 inch studs.The main features of the Neumann EA 87 SILVER include:Essential elastic suspension mount for all U 87 usersNickel (silver) finishSwivel mount with a 5/8 inch-27 female thread, plus a thread adapterReduce rumble and noise transferred through the microphone stand For more information, please visit this products webpage
Neumann EA 89 A mtThe EA 87 is designed for the U 87 Ai microphone. It has a swivel mount with a 5/8"-27 female thread, plus a thread adapter to connect to 1/2"- and 3/8" studs. For more information, please visit this products webpage
Neumann IC 5 mtMicrophone cable with double twist (double helix) braiding as shield. Diameter 5 mm, length 10 m. XLR 5 connectors.Other cable lengths are available upon request! Cable material without connectors are also available.Even if very long (Neumann) cables are used, the electroacoustic characteristics of the microphone are not affected.Only with cable lengths well over 300 m a high-frequency roll-off is noticeable. For more information, please visit this products webpage
Neumann is excited to introduce its latest innovation, the KH 120, representing the first product in the new line of Neumann Studio Monitors.
The KH 120 A studio monitor is designed for use as a near-field loudspeaker or as a rear loudspeaker in larger multi-channel systems. The KH 120 A represents the latest in acoustic and electronic simulation and measurement technologies to ensure the most accurate sound reproduction possible. It has a Mathematically Modeled Dispersion waveguide (MMD (TM), flexible acoustical controls, analog class-AB amplifiers, a large headroom analog input and an extensive mounting hardware range. All of this provides the user with the maximum versatility over a wide variety of acoustic conditions, source equipment, and physical locations.
The KH 120 is perfect for tracking, mixing and mastering in music, broadcast, project and post-production studios.
Features
Product Feature Benefit to the Customer
Powerful titanium fabric dome
Low-distortion high-frequency reproduction
Elliptical Mathematically Modelled Dispersion™
(MMD™) waveguide
Smoother off-axis response,
More forgiving of diverse acoustical environments
Composite sandwich cone
Damping of break-up modes
Long throw bass driver
Low distortions at high sound levels
Two-color + dimmable Neumann logo
Displays operation status and activation of the extensive protection system
Robust metal grille
Protects against mechanical damage
Large front panel ports
Reduced bass compression and easier to mount in tight spaces such as OB vans
Compact aluminum cabinet
(magnetically shielded)
Minimizes resonances, better heat dissipation, long life
Wide horizontal dispersion
Freedom of movement across the mixing console
Narrow vertical dispersion
Reduces reflections off the mixing console
One-piece front panel with no discontinuities
Reduced diffraction and smoother frequency response
Powerful analog amplifiers with large headroom
Improved transient response
Production consistency
Any KH 120 is “pair-matched” to any other KH 120
4-position bass, low-mid and treble acoustical controls
More control in diverse acoustical environments
Wide range input gain and output level controls
Easier interfacing with signal sources
New mounting hardware options
More flexibility in mounting cabinets in more diverse locations
Display dimmer
For low lighting level conditions or behind the screen applications
Ground lift
Reduced noise in electrically noisy environments and over-comes ground loops
Universal switched-mode power supply
(100 … 240 V)
One version works in any country and robust to poor quality mains supply
Separate woofer and tweeter electronic peak limiters and thermal-protection circuitry
High reliability
Technical Data
Acoustics
-3 dB free field frequency response 52 Hz … 21 kHz, ± 3 dB
Pass band free field frequency response 54 Hz … 20 kHz, ± 2 dB
Self-generated noise
(with input gain set to 100 dB for 0 dBu) <20 dB(A) at 10 cm
Sine wave output with a THD < 0.5 % at 1 m 100 Hz @ 95 dB SPL
Max. SPL In half space at 3% THD at 1m 111.1 dB SPL
(averaged between 100 Hz and 6 kHz)
Max SPL with pink noise in a typical installation 92 dB(C) at 2.3 m, (full range)
94 dB(C) at 2.3 m (with KH 810)
Electronics
Woofer amplifier, cont.(peak) output power* 50 W (80 W)
Tweeter amplifier, cont.(peak) outputpower* 50 W (80 W)
Controller design Analog, active
Crossover Frequency 2.0 kHz
Crossover Slope (dB/oct.) 24, 4th order
Equalization - Bass 0, -2.5, -5, -7.5 dB
Equalization - Mid 0, -1.5, -3, -4.5 dB
Equalization - High +1, 0, -1, -2 dB
Protection circuitry Limiter: low, high
Infrasonic filter frequency; slope 30 Hz; 6 dB/oct.
Analog Input
Impedance, electrically balanced
10k Ohms in position 94/108 dB SPL at 1 m
20k Ohms in position 100/114 dB SPL at 1 m
Input gain control (sensitivity) 0 dBu to -15 dBu
Output level control 94, 100, 108, 114 dB SPL
CMRR >56 dB @ 15 kHz
Maximum input level 24 dBu
Displays and Mains Power
Displays and indicators - power on Neumann logo “White”
Displays and indicators - limit/clip Neumann logo “Red”
Mains Power Supply, voltage; frequency 100-240 V~; 50/60 Hz
Power consumption – Idle 20 W
Power consumption – Full output AC 200 W
Mechanics
Cabinet surface finish, color: custom Painted aluminium, Anthracite (RAL 7021)
Operating conditions +10° C to +40° C (+50° F to +104° F),
<90% RH, non-condensing
Transport/storage conditions −25° C to +70° C (−13° F to 158° F),
<90% RH, non-condensing
Drivers Magnetically shielded
Woofer 130 mm (5.25”)
Tweeter 25 mm (1”)
Mounting points 2 x M8 on rear panel
Height x width x depth, mm (inches) 277 x 182 x 220 mm (10 7/8” x 7 1/8” x 8 5/8”)
Internal net volume / external volume 6.5 liters / 9.7 liters
Weight 6.2 kg (13.7 lbs)
Neumann is excited to introduce its latest innovation, the KH 120, representing the first product in the new line of Neumann Studio Monitors. The KH 120 A studio monitor is designed for use as a near-field loudspeaker or as a rear loudspeaker in larger multi-channel systems. The KH 120 A represents the latest in acoustic and electronic simulation and measurement technologies to ensure the most accurate sound reproduction possible. It has a Mathematically Modeled Dispersion waveguide (MMD (TM), flexible acoustical controls, analog class-AB amplifiers, a large headroom analog input and an extensive mounting hardware range. All of this provides the user with the maximum versatility over a wide variety of acoustic conditions, source equipment, and physical locations.The KH 120 is perfect for tracking, mixing and mastering in music, broadcast, project and post-production studios.Features
Product Feature Benefit to the Customer
Powerful titanium fabric dome
Low-distortion high-frequency reproduction
Elliptical Mathematically Modelled Dispersion™
(MMD™) waveguide
Smoother off-axis response,
More forgiving of diverse acoustical environments
Composite sandwich cone
Damping of break-up modes
Long throw bass driver
Low distortions at high sound levels
Two-color + dimmable Neumann logo
Displays operation status and activation of the extensive protection system
Robust metal grille
Protects against mechanical damage
Large front panel ports
Reduced bass compression and easier to mount in tight spaces such as OB vans
Compact aluminum cabinet
(magnetically shielded)
Minimizes resonances, better heat dissipation, long life
Wide horizontal dispersion
Freedom of movement across the mixing console
Narrow vertical dispersion
Reduces reflections off the mixing console
One-piece front panel with no discontinuities
Reduced diffraction and smoother frequency response
Powerful analog amplifiers with large headroom
Improved transient response
Production consistency
Any KH 120 is “pair-matched” to any other KH 120
4-position bass, low-mid and treble acoustical controls
More control in diverse acoustical environments
Wide range input gain and output level controls
Easier interfacing with signal sources
New mounting hardware options
More flexibility in mounting cabinets in more diverse locations
Display dimmer
For low lighting level conditions or behind the screen applications
Ground lift
Reduced noise in electrically noisy environments and over-comes ground loops
Universal switched-mode power supply
(100 … 240 V)
One version works in any country and robust to poor quality mains supply
Separate woofer and tweeter electronic peak limiters and thermal-protection circuitry
High reliability
Technical Data
Acoustics
-3 dB free field frequency response 52 Hz … 21 kHz, ± 3 dB
Pass band free field frequency response 54 Hz … 20 kHz, ± 2 dB
Self-generated noise
(with input gain set to 100 dB for 0 dBu) <20 dB(A) at 10 cm
Sine wave output with a THD < 0.5 % at 1 m 100 Hz @ 95 dB SPL
Max. SPL In half space at 3% THD at 1m 111.1 dB SPL
(averaged between 100 Hz and 6 kHz)
Max SPL with pink noise in a typical installation 92 dB(C) at 2.3 m, (full range)
94 dB(C) at 2.3 m (with KH 810)
Electronics
Woofer amplifier, cont.(peak) output power* 50 W (80 W)
Tweeter amplifier, cont.(peak) outputpower* 50 W (80 W)
Controller design Analog, active
Crossover Frequency 2.0 kHz
Crossover Slope (dB/oct.) 24, 4th order
Equalization - Bass 0, -2.5, -5, -7.5 dB
Equalization - Mid 0, -1.5, -3, -4.5 dB
Equalization - High +1, 0, -1, -2 dB
Protection circuitry Limiter: low, high
Infrasonic filter frequency; slope 30 Hz; 6 dB/oct.
Analog Input
Impedance, electrically balanced
10k Ohms in position 94/108 dB SPL at 1 m
20k Ohms in position 100/114 dB SPL at 1 m
Input gain control (sensitivity) 0 dBu to -15 dBu
Output level control 94, 100, 108, 114 dB SPL
CMRR >56 dB @ 15 kHz
Maximum input level 24 dBu
Displays and Mains Power
Displays and indicators - power on Neumann logo “White”
Displays and indicators - limit/clip Neumann logo “Red”
Mains Power Supply, voltage; frequency 100-240 V~; 50/60 Hz
Power consumption – Idle 20 W
Power consumption – Full output AC 200 W
Mechanics
Cabinet surface finish, color: custom Painted aluminium, Anthracite (RAL 7021)
Operating conditions +10° C to +40° C (+50° F to +104° F),
<90% RH, non-condensing
Transport/storage conditions −25° C to +70° C (−13° F to 158° F),
<90% RH, non-condensing
Drivers Magnetically shielded
Woofer 130 mm (5.25”)
Tweeter 25 mm (1”)
Mounting points 2 x M8 on rear panel
Height x width x depth, mm (inches) 277 x 182 x 220 mm (10 7/8” x 7 1/8” x 8 5/8”)
Internal net volume / external volume 6.5 liters / 9.7 liters
Weight 6.2 kg (13.7 lbs)
Neumann is excited to introduce its latest innovation, the KH 120, representing the first product in the new line of Neumann Studio Monitors. The KH 120 A studio monitor is designed for use as a near-field loudspeaker or as a rear loudspeaker in larger multi-channel systems. The KH 120 A represents the latest in acoustic and electronic simulation and measurement technologies to ensure the most accurate sound reproduction possible. It has a Mathematically Modeled Dispersion waveguide (MMD (TM), flexible acoustical controls, analog class-AB amplifiers, a large headroom analog input and an extensive mounting hardware range. All of this provides the user with the maximum versatility over a wide variety of acoustic conditions, source equipment, and physical locations.The KH 120 is perfect for tracking, mixing and mastering in music, broadcast, project and post-production studios.Features
Product Feature Benefit to the Customer
Powerful titanium fabric dome
Low-distortion high-frequency reproduction
Elliptical Mathematically Modelled Dispersion™
(MMD™) waveguide
Smoother off-axis response,
More forgiving of diverse acoustical environments
Composite sandwich cone
Damping of break-up modes
Long throw bass driver
Low distortions at high sound levels
Two-color + dimmable Neumann logo
Displays operation status and activation of the extensive protection system
Robust metal grille
Protects against mechanical damage
Large front panel ports
Reduced bass compression and easier to mount in tight spaces such as OB vans
Compact aluminum cabinet
(magnetically shielded)
Minimizes resonances, better heat dissipation, long life
Wide horizontal dispersion
Freedom of movement across the mixing console
Narrow vertical dispersion
Reduces reflections off the mixing console
One-piece front panel with no discontinuities
Reduced diffraction and smoother frequency response
Powerful analog amplifiers with large headroom
Improved transient response
Production consistency
Any KH 120 is “pair-matched” to any other KH 120
4-position bass, low-mid and treble acoustical controls
More control in diverse acoustical environments
Wide range input gain and output level controls
Easier interfacing with signal sources
New mounting hardware options
More flexibility in mounting cabinets in more diverse locations
Display dimmer
For low lighting level conditions or behind the screen applications
Ground lift
Reduced noise in electrically noisy environments and over-comes ground loops
Universal switched-mode power supply
(100 … 240 V)
One version works in any country and robust to poor quality mains supply
Separate woofer and tweeter electronic peak limiters and thermal-protection circuitry
High reliability
Technical Data
Acoustics
-3 dB free field frequency response 52 Hz … 21 kHz, ± 3 dB
Pass band free field frequency response 54 Hz … 20 kHz, ± 2 dB
Self-generated noise
(with input gain set to 100 dB for 0 dBu) <20 dB(A) at 10 cm
Sine wave output with a THD < 0.5 % at 1 m 100 Hz @ 95 dB SPL
Max. SPL In half space at 3% THD at 1m 111.1 dB SPL
(averaged between 100 Hz and 6 kHz)
Max SPL with pink noise in a typical installation 92 dB(C) at 2.3 m, (full range)
94 dB(C) at 2.3 m (with KH 810)
Electronics
Woofer amplifier, cont.(peak) output power* 50 W (80 W)
Tweeter amplifier, cont.(peak) outputpower* 50 W (80 W)
Controller design Analog, active
Crossover Frequency 2.0 kHz
Crossover Slope (dB/oct.) 24, 4th order
Equalization - Bass 0, -2.5, -5, -7.5 dB
Equalization - Mid 0, -1.5, -3, -4.5 dB
Equalization - High +1, 0, -1, -2 dB
Protection circuitry Limiter: low, high
Infrasonic filter frequency; slope 30 Hz; 6 dB/oct.
Analog Input
Impedance, electrically balanced
10k Ohms in position 94/108 dB SPL at 1 m
20k Ohms in position 100/114 dB SPL at 1 m
Input gain control (sensitivity) 0 dBu to -15 dBu
Output level control 94, 100, 108, 114 dB SPL
CMRR >56 dB @ 15 kHz
Maximum input level 24 dBu
Displays and Mains Power
Displays and indicators - power on Neumann logo “White”
Displays and indicators - limit/clip Neumann logo “Red”
Mains Power Supply, voltage; frequency 100-240 V~; 50/60 Hz
Power consumption – Idle 20 W
Power consumption – Full output AC 200 W
Mechanics
Cabinet surface finish, color: custom Painted aluminium, Anthracite (RAL 7021)
Operating conditions +10° C to +40° C (+50° F to +104° F),
<90% RH, non-condensing
Transport/storage conditions −25° C to +70° C (−13° F to 158° F),
<90% RH, non-condensing
Drivers Magnetically shielded
Woofer 130 mm (5.25”)
Tweeter 25 mm (1”)
Mounting points 2 x M8 on rear panel
Height x width x depth, mm (inches) 277 x 182 x 220 mm (10 7/8” x 7 1/8” x 8 5/8”)
Internal net volume / external volume 6.5 liters / 9.7 liters
Weight 6.2 kg (13.7 lbs)
Allgemeine Beschreibung
Der Studiomonitor KH 120 D ist als Nahfeldlautsprecher oder hinterer Lautsprecher in größeren Mehrkanalsystemen konzipiert. Er verkörpert modernste akustische und elektronische Simulations- und Messtechnologien und garantiert höchstmögliche klangliche Präzision. Der KH 120 D zeichnet sich aus durch ein Mathematically Modeled Dispersion Waveguide™ (MMD™), universelle Akustikregler, analoge Class-AB Verstärker sowie verschiedene Eingangsformate und eine breite Palette an Montagehardware. Dies bietet Ihnen maximale Flexibilität im Umgang mit akustischen Bedingungen, Quellengeräten und Aufstellungsorten.
Der KH 120 D ist das perfekte Werkzeug zum Aufnehmen, Mischen und Mastern in Musik-, Sende-, Projekt- und Post Production-Studios.
Produktmerkmale
Leistungsstarke Titan-Gewebekalotte
Elliptisches Mathematically Modelled Dispersion™ (MMD™) Waveguide
Composit-Sandwich-Membran
Langer linearer Hub
Zweifarbiges, dimmbares Neumann-Logo
Robustes Metallgitter
Große vorderseitige Bassreflexkanäle
Kompaktes Aluminiumgehäuse (magnetisch geschirmt)
Breite horizontale Abstrahlcharakteristik
Schmale vertikale Abstrahlcharakteristik
Absolut homogene, verrundete Schallwand
Großzügig dimensionierte Analogverstärker
Produktkonsistenz (Jeder KH 120 bildet mit jedem beliebigen zweiten ein perfektes Paar)
4-stufige Akustikregler für Bass, Low-Mid und Treble
Flexible Eingangs-/Ausgangspegelregler
Neue Montagehardware-Optionen
Display-Dimmer
Ground Lift
Universelles Weitbereichs-Netzteil (100 … 240 V)
XLR-Analogeingang
Digitaler BNC-Eingang und gepufferter BNC-Ausgang
Elektronische Peak-/Thermo-Limiter-Schutzschaltung getrennt für Woofer und Tweet
Lipsync Delay (0 … 12/12 Frames)
Laufzeitverzögerung (0 … 400 ms)
Features:
Hochpräzise Treiber, Mathematically Modelled Dispersion™ (MMD™) Waveguide
Linearer Frequenzgang 44 Hz … 21 kHz (±3 dB)
Linearer Phasengang 120 Hz … 16 kHz (±45°) mit Latenz <2,6 ms
DSP-Engine ermöglicht eine raumadaptive Kalibrierung über Neumanns MA 1
Messerscharfe Lokalisation dank extrem geringer Toleranzen (±0,5 dB)
Kann mit anderen KH-Lautsprechern in Immersive/Surround-Setups kombiniert werden.
Neumann KH 310 A - Active Studio Monitor
The KH 310 three-way active tri-amplified monitor features a Mathematically Modeled Dispersion™ Waveguide (MMD™), flexible acoustical controls, various input options and an extensive range of mounting hardware. This allows the loudspeaker to be used in diverse acoustical conditions, with any source equipment and in a wide variety of physical locations. The KH 310 represents the latest in acoustic and electronic simulation and measurement technologies to ensure the most accurate sound reproduction possible.The KH 310 is designed for use as a near-field monitor, as a front loudspeaker in mid-sized multi-channel systems, or as a rear loudspeaker in a larger multi-channel system. It can be used in project, music, broadcast centers, OB vans, and post production studios for tracking, mixing, and mastering.
Three-way tri-amplified monitor with thermally protected 90 + 90 + 210 W class A/B-amplifiers
Limit and clip indicated by dimmable logo LED
Magnetically shielded 1" alloy fabric dome tweeter
3" soft dome midrange
8 1/4" composite-sandwich membrane woofer
Tweeter protected by grille
Compact cabinet molded from low-resonance materials with waveguide integrated into the front baffle
Separate left and right versions
>10 kOhm electronic-balanced input on XLR-F with ground lift
Fourth-order crossover, and four-position "Bass", "Low-Mid" and "Treble" acoustical controls
Independent thermo limiters for woofer, midrange and tweeter
Woofer soft clip and excursion limiters
Maximum SPL is 120.2 dB at 1 m (3% THD)
bass capability is 111.6 dB at 1 m (max SPL at 3% THD between 50-100 Hz)
pass band frequency response 34 Hz - 21 kHz (-3 dB)
Self-generated noise level <0 dB(A) at 1 m
Cabinet volume 16.2 liters
Dimension: 253 x 383 x 292 mm (10" x 15 1/8" x 11 1/2"), and weight 13.0 kg (28 lbs 11 oz)
Two M8 threads on side panel for attaching to mounting hardware and rear panel bracket. Optional metal grille
Standard cabinet color: RAL 7021 (anthracite)
Powerful alloy fabric dome:
Low-distortion high-frequency reproduction
Elliptical Mathematically Modeled Dispersion™ (MMD™) waveguide, with wide horizontal and narrow vertical dispersion:
Smoother off-axis response
More forgiving of diverse acoustical environments
Freedom of movement across the mixing console
Reduces reflections off the mixing console
New in-house simulated drivers:
Latest modeling techniques used to minimize non-linear (intermodulation) distortion
Fabric dome, neodymium magnet, midrange driver:
Dedicated driver reproduces important midrange frequencies, which is especially important for speech and vocals
Light weight dome has better transient response and less breakup modes than cone designs
High power magnet reduces harmonic and intermodulation distortion
Long throw composite sandwich cone bass driver with Extremely Linear Force Factor™ (ELFF™) and ribbed surround:
Damping of break-up modes and low distortion at high sound levels
Linear pistonic motor gives a very low harmonic distortion even at high excursions
Reduced radial break-up modes on the ribbed surround
Two-color + dimmable Neumann logo:
Displays operation status and activation of the extensive protection system
Dimmable for low lighting level conditions or behind the screen applications
Compact sealed three-way cabinet design (magnetically shielded):
No standing wave resonances
Fastest bass transient response
Reduced intermodulation distortion in midrange
One-piece front panel with no discontinuities:
Reduced diffraction and smoother frequency response
Powerful analog class AB amplifiers with large headroom:
Improved transient response
Independent thermo limiters for woofer, midrange dome and tweeter to protect the voice coils. Woofer soft clip and excursion limiters:
Fast acting
High reliability
Allows extraction of the maximum performance from the system
Production consistency due to individual hand-alignment in final test:
Any KH 310 is “pair-matched” to any other KH 310
4-position bass, low-mid and treble acoustical controls:
More control in diverse acoustical environments
Wide range input gain and output level controls:
Easier interfacing with signal sources
Ground lift:
Reduced noise in electrically noisy environments and over-comes ground loops
Universal switched-mode power supply (100 … 240 V):
One version works in any country and robust to poor quality mains supply
Extensive mounting hardware options:
More flexibility in mounting cabinets in more diverse locations
Backwards compatibility with previous models
Optional robust metal grille:
Can be used, if required, to protect the drivers
Optional transportation accessories:
Stylish soft carry bag with space for cables
Robust wooden flight case
€1,842.00*
Diese Website verwendet Cookies, um eine bestmögliche Erfahrung bieten zu können. Mehr Informationen ...